• The Gear Page Apparel & Merch Shop is Open!

    Based on member demand, The Gear Page is pleased to announce that our Apparel Merch Shop is now open. The shop’s link is in the blue Navigation bar (on the right side), “Shop,” with t-shirts, hats, neck buffs, and stickers to start. Here’s the direct link: www.thegearpageshop.com

    You’ll find exclusive high-quality apparel and merchandise; all items are ethical, sustainably produced, and we will be continuously sourcing and adding new choices. 

    We can ship internationally. All shipping is at cost.


Search results

  1. deadhead

    Vintage Peavey wiring question

    Thank you both and thank you @J M Fahey for following up for additional questions I had. Really appreciate the information and help
  2. deadhead

    Vintage Peavey wiring question

    Appreciate the reply! The manual you provided is actually for the model that came after the one I have. I can’t find any documentation of the amp I have and when I contacted Peavey they provided the same manual. Was hoping they would have some kind of info on this amp... Thanks for the...
  3. deadhead

    Vintage Peavey wiring question

    Hey all, I've got a pretty old Peavey Standard 240 that I am going to replace the 2-prong power cable on. Looking at the current wiring, I believe this will be a simple swap but wanted to get confirmation on a couple things.... Peavey Standard 240 Referencing the photo linked above: 1...
  4. deadhead

    Volume swells via expression pedal MIDI

    With my Source Audio C4 I use one preset as a dry signal 'volume swell'. Basically just using the pedal as a bypass and controlling the volume with the expression pedal. YMMV
  5. deadhead

    Mattson 2 (Jared Mattson) Rig Rundown

    Caught these guys at La Bodega Gallery in San Diego. Loved their stuff!
  6. deadhead

    Ultimate Chorus Repair - What is this?

    Alright, so I re-flowed the solder around one of the tabs that was free moving a bit (far right in photo). The connection seems to be in tact as I do notice ohms running through the place.
  7. deadhead

    Ultimate Chorus Repair - What is this?

    So if I touch the multimeter prongs to the plate itself, I am picking up and ohm reading. With this, it seems that the connection to the tabs through the board is still in tact. I did notice the third tab from the left is free moving, so I will re-solder that when I am replacing the pot. I'm...
  8. deadhead

    Ultimate Chorus Repair - What is this?

    Interestingly, I saw a video on YouTube of a guy fixing some cold joints on one of these and I noticed the plate leaned onto the input jacks of that one as well :dunno
  9. deadhead

    Ultimate Chorus Repair - What is this?

    @jdh So there are three points in which the tabs are soldered through the board. I ran a multimeter on them and they are picking up an ohm reading if I connect the prongs to the two 2 left legs in the photo below. I am getting no reading from positive on one of those tabs to ground Not sure...
  10. deadhead

    Ultimate Chorus Repair - What is this?

    Thanks for the information! Yes the unit does work now and sounds great. The reverb pot was busted so I opened it up to replace that. I did notice a bit of rattling when the volume was up, and now I know why :) I'm going to finish getting the board out of the chassis and flip it over to...
  11. deadhead

    Ultimate Chorus Repair - What is this?

    Thanks. So I had the multimeter on, positive to the plate, negative on ground. No response. With this, I am guessing this is acting as a shield to the input jacks as @Chris Kline mentioned? Looking at the service manual, doesn't look like this plate is identified as anything electrical...
  12. deadhead

    Ultimate Chorus Repair - What is this?

    Thanks If checking continuity I’m assuming I should power the amp on? With a solid state amp, could I turn it on without a speaker load?
  13. deadhead

    Ultimate Chorus Repair - What is this?

    Gotcha. Yeah I can see the little tabs where its supposed to sit into the board a bit. I suppose I can remove some of the glue and set it back upright, then glue again to hold it in place. Curious what purpose it serves?
  14. deadhead

    Ultimate Chorus Repair - What is this?

    Hey all, Snagged a Fender Ultimate Chorus over the weekend for a great deal. Had a busted reverb pot so I took the board out to replace that. In the process I noticed that this metal sheet is no longer held up by the glue and folding over. See photos below: This is fairly new territory...
  15. deadhead

    Variable high pass filter pedal

    This, have the H/LPF
  16. deadhead

    Which pedal is better at 18v?

    Try both and see which one you prefer?
  17. deadhead

    Strictly FUZZ

    Smallsound/Bigsound - Team Awesome Fuzz Machine :aok
  18. deadhead

    EHX 720 Looper noise?

    Yeah sounds like that’s the best route!
  19. deadhead

    Wiring schematic for DPDT switches

    Hey! I ended up following the schematic found at the bottom of this thread: https://forum.seymourduncan.com/showthread.php?316285-in-need-of-68-Teisco-Barth-wiring-schematic The switch wiring differs from the 'stock' wiring, so they run in series (getting a bump in volume for both on) I...
  20. deadhead

    EHX 720 Looper noise?

    You're not alone, I've had similar experiences when looking for help here. For what its worth, I have a 720 looper and have not experienced any noise issues. Currently powering the unit off of a One-spot that is also connected to a few fuzz pedals. Then again, I use single coils through a tube...
  21. deadhead

    Wiring schematic for DPDT switches

    Thanks for the help! Does this look correct? Would I just wire the pots to the 60s Tele spec as well?
  22. deadhead

    Wiring schematic for DPDT switches

    Bump so I can get this thing wired up!
  23. deadhead

    Wiring schematic for DPDT switches

    I am trying to re-wire an old Japanese guitar I have but unsure about the way I wire the two DPDT on/off switches with the pickups. The switches are the slide style on/off with six poles. Does anyone know how I would wire the two single coil pickups to these switches and out? I can’t seem to...
Top