kemper freezing?

Discussion in 'Digital & Modeling Gear' started by jzucker, Feb 16, 2015.

  1. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    Using firmware 2.7.4

    • On occasion, i'm seeing the UI lock up to the point where I have to shut down and restart the kemper. Have seen this happen twice now with this firmware rev.
    • I've also seen a variation of this where in performance mode, I cannot select a new rig using the type selector. I select the type but it never loads and eventually times out and reverts back to the original rig. Unlike the previous issue, the problem goes away when I unplug the USB cable so it seems as if an operation failed to complete.
    • At first I thought it was rig manager but it just happened again without rig manager being involved. Seems like it's getting into a runaway CPU condition because when I turned the selector off it took about 10 seconds before it began the shutdown sequence.

    Anyone else seeing this?
     
  2. Calaban

    Calaban Member

    Messages:
    2,070
    Joined:
    Jul 30, 2009
    I have not had this problem. The only issue I have ever had was a "corrupted" profile on startup...the Kemper ran some kind of repair and everything has been fine since.

    I'm sure the answer is 'yes', but have you done a full system reset?
     
  3. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    actually I have not done a full reset since upgrading to 2.7.4
     
  4. Calaban

    Calaban Member

    Messages:
    2,070
    Joined:
    Jul 30, 2009
  5. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    Thanks, I'll do that tonight but I'm starting to feel a bit uneasy, lol.
     
  6. ClassicLP

    ClassicLP Member

    Messages:
    1,204
    Joined:
    Dec 15, 2014
  7. trazan

    trazan Member

    Messages:
    807
    Joined:
    May 13, 2006
    Location:
    Norway
    I've had this happen a long time ago when I browsed quickly through rigs with Autoload on.
     
  8. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    That sounds right because I keep autoload on. If it's off do you press the store button or something else to load the selection?
     
  9. trazan

    trazan Member

    Messages:
    807
    Joined:
    May 13, 2006
    Location:
    Norway
    When Autoload is off, the same soft button becomes a flashing Load button :)
     
  10. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    Thanks! I'll bet that's the issue!
     
  11. pepi

    pepi Member

    Messages:
    870
    Joined:
    Jan 23, 2005
    Location:
    Central Indiana
    Probably a virus or Malware :)

    Do you get any pop-up about coupons

    [​IMG]
     
    Last edited: Feb 17, 2015
  12. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    I think this forum wins hand's down for the most stalkers and trollers.
     
  13. RackFiz

    RackFiz Member

    Messages:
    465
    Joined:
    Apr 25, 2013
    ...or, you might be too sensitive to others questioning your knowledge base and or capability.
     
  14. jzucker

    jzucker Supporting Member

    Messages:
    20,303
    Joined:
    May 20, 2003
    Location:
    Home of the ex-world champion Cavs
    bad news is that I did not have auto-load on. So that's not the issue.
     
  15. ClassicLP

    ClassicLP Member

    Messages:
    1,204
    Joined:
    Dec 15, 2014

Share This Page